Audi A3 parts reviews

5-6k. It depends on how much you push the car. Hard acceleration and high revs will require more frequent oil changes.

Audi A3 spark plugs work like a charm. Stage 2+ & fully upgraded supporting hardware.

BNT are good for brake stuff - they normally have two options, their cheaper brand and brembo. Did rotors and pads front and rear on an Audi A3 for $650 for brembo rotors and Bendix pads as an indication.

Changed air filter (Mann) oil filter (Mann) and oil, Liqui Moly Molygen 5w40. it's only VW 502 00 'recommended' but that shouldn't be an issue, plan to oil-change every 7k KMs.

I went with Bosch QuietCast rotors and pads . The Akebono pads performed well, but wore out faster than I'd expected. I don't know if the low wear on them caused scoring of the rotors or if it was the calipers not doing a proper job... but I did not detect a loss in brake performance, which was really strange. This was happening to the rear, so maybe the front end brake system was compensating.

my consumption was terrible when running Castrol .... Now it's pretty decent .... Especially for winter time .... Liquimoly is ace.

It helped significantly! Went from burning Castrol to liquimoly which burns way less. Also I use a liquimoly sealer now and then to reduce consumption.

I went with ECS's slotted rotors for both the front and rear, and EBC Redstuff pads all around. With new fluid, they've been great across the board. Less dust than the OEM pads in my experience, less fade, better performance all around

Some people will get an error when trying to get their xenons to go into adaptation mode. I played with my setup and got a MIL. My rear level sensor is a good bit off, so it throws my xenons off no matter what. Ill need to tap a new hole and play with positioning in order to get the measurement back to where the car will auto adjust again. Ill let u guys know what I come up with, along with a really easy to follow write up.

I bought a 13" replacement blade from the local Wal-Mart: manufacturer 'Anco', part number 31-13. Price at my store was $4.57. It looked like it would slip right in to replace the entire wiper & blade assembly... but unfortunately, the 'cage' is too wide, and it won't fit into the A3 rear wiper receiver. -So -having spent the money & opened the pack, I decided to try using the blade and metal reinforcing 'springs' in the old (Audi OEM) wiper blade. I had to bend one 'claw' of the replacement Anco blade open, to get the new insert and metal strips out (the strips have a 'lock' which prevents them sliding out). Then I had to persuade the OLD rubber blade and spring-steel reinforcement strips out of the OEM blade assembly. -This was a bit tricky, but I was able to to slide them out. Then I slipped the new rubber and metal reinforcement strips into the old OEM blade assembly... but be sure to slip the 'clip' end in LAST, and also make sure that the three little 'teeth' on the inside faces are alongside the rubber, so that they grip it and prevent it from slipping out. UNFORTUNATELY... the replacement 'blades' are about a quarter of an inch too short, and the end away from the clips doesn't support the rubber all the way to the furthest 'claw'. -This means that if you try to run them this way, the rubber will eventually slip out from the end of the blade, leaving the 'claw' to scratch the glass. I bodged a 'fix' by re-using the OLD metal blades AS WELL AS the new ones. -You have to do this on both sides. -It's an absolute bugger to get them in all the way, would probably be a little easier if you 'lubed' up the slots that they have to slide in (the rubber slots alongside the other metal blades) with a dish soap solution or something similar, but -using a pair of pliers and some creative curse words, I got them to slide in. So... for less than five bucks I got something to work. HOWEVER... It's about a quarter of an inch shorter than the OEM blade, it's a WHOLE lot of farting around, and I think every time I do this from this point onward, I'm going to just buy the OEM blade and have done with it. -The saving is about $3, and the hassle and all of the fiddling simply isn't worth it.