Brake caliper Brembo or OEM Porsche

Ok, so i got them fitted yesterday. I used the following: - caliper carripers from Epytec for the cayenne zr18 caliper for mk4 : http://www.epytec.de/modelle/vw/gol...achse/1293/adapter-porsche-bremssattel-audi-tt-a3-vw-golf-4-polo-9n-bora?c=1250 - braided brake hoses from Epytec for porsche calipers: http://www.epytec.de/kategorien/bre...ng-vw-golf-4-r32-audi-a3-s3-a1-porsche-brembo-ttrs-polo-9n-bremsen-umbau?c=1730 - regular ATE brake pads - EBC R32 Brake discs - Porsche Cayenne ZR18 calipers I ended up having to put my 20mm spacers from the back wheels to the front, because the 10mm ones didn't clear the caliper. The epytec hardware is really good quality stuff, comes with all necesary german TUV paperwork to be able get the brakes \"registered\". I drove a total of 10 miles, and as a first impression, the pedal is kind of spongy and goes down pretty low. I will definitely look into upgrading to a 25.4mm M/C. I will let you guys know more after the brakes get seated in properly and do a really good brake bleeding to a better brake fluid.

I did the Brembo 18Z(Touareg/Cayenne/Q7 calipers) on mine. It wound up being relatively cheap, less than $1000, but I used normal powerslot slotted rotors not 2 piece fancy rotors. They were relatively cheap and look awesome. Wheel clearance is a MAJOR issue, finding wheels to clear with anywhere near stock offset is very hard. They do NOT have bias issues that some people complain about when putting them on other MKV and MKVI cars, I would say my car brakes in a very balanced way.

I'd go with Porsche calipers on stock rotors, which is what I run. MUCH improved pedal feel and modulation, ability to swap pads without taking the caliper off, and more pad options.

I've got an Audi A4 Quattro that I DD, Autocross and teach HPDE ( Track Days ). Originally I tried the TT carrier / A8 rotor (312mm ) upgrade. I later switched to Porsche Boxster calipers because I was getting pad taper on Track Days.

Rear calipers are a Porsche 944T, the disks in a VW Corrado / Golf G60, 280mm, 274mm lowered to the clamps are anchored with an adapter for Grinling54, is to lower a bit with the grinder, but it is simple

I currently have 12.3" Audi TT rotors with Porsche 911 (996) calipers. Those brakes works fine, but I want smaller brakes so I can fit 15" wheels.

I run TT rotors with Boxster calipers. I like this setup very much. Brake pedal is a little firmer than stock and they are easy to modulate on the street.

I have the Seat Ibiza Cupra R 4 pot Brembos for a 4 lug 12" rotors I'm running Brock B2's 16x7.5" with a 15mm FK spacer.

No fade at all (overheating is no longer an issue). For the first time the brake pedal feels like the gas pedal. You just touch it and it slows down a bit, you gently step on it and it slows you down, you press harder and it slows you even faster, etc. Finally, believe it or not, ABS kicks in rarely!! (not the case with OEM brakes). My opinion is that this is a very wise setup, not \"ricey\", very effective and a top value for money .

ok so last weekend i did 312mm rotors, porsche boxster calipers and stainless lines. i had g60 brakes previous. i bled them out nooooooo air. drove the car and expected to stand it on it nose. brakes no better than what i had, maybe worse.