Brake pads Ferodo or WAGNER

If you want a bit more performance without loosing cold braking, use ferodo ds performance, they're amazing price-quality wise.

Wagner thermoquiet here. Works perfectly.

I’ve used Wagner thermoquiet pads and the cheapest wholesale close out rotor with good results.

Bosch and Wagner rotors and ceramic pads are my preferred brands. I put new Wagner front brake pads on the Frontier 5 1/2 years ago and they still have about 3mm left.

Ferodo DS2500 paired with Zimmerman blank rotors and Motul RBF600 is what I use. The tracks I go to are more technical and not fast so it's great for my use case. I imagine if I went to a track where speeds are above 150Km/H and have long, fast corners, I would need better pads. I'm considered intermediate to advanced and last ran a 1:47 at CTMP DDT with worn Vitour Tempesta Enzo tires. I think I can run low 40s this year. I would not track with stock pads. I overheated my pads and brake fade hit hard. The pads melted and I went off the track and almost over the hill at TMP (Cayuga).

I used DS2500 for my first 2 track days but outgrew them rather quickly on a 2800 lb car. Last time I swapped to DS1.11 and felt much more confident braking deeper into corners with zero fade at my intermediate level. Now I just use DS2500 for the street and canyons.

if you want raw stopping power then Ferodo DS2500's are great.

I switched to the Ferodo DSUno. I am satisfied with its performance, but they seem to struggle because of something. Today, after the track day on Saturday, I checked it and found a crack and a gnawed edge. Also, they have uneven wear, about 0.5-1mm difference. The differences are between the top and bottom parts of the pads, front and back parts and on different sides of the same rotor (inner and outer pads). Uneven wear was with the old pads as well. Recently, I installed brake air ducts, and after going out from the track, the temperature was, in the worst case, 480C degree, which looks fine for these pads. In total, I drove for about 3 hours on tracks, one on a wet track (so no hard braking) and two moderately/hard(8-9/10) braking. The brake rotors are also new, Zimmermann blank, installed with pads. The initial thickness of the pads is 16.4mm (with the plate, the plate is 5.5mm, so the "pure" pad is about 11mm) Currently, I have eaten about 4.5-5mm of the pads in 3 hours of tracking.

Recently completed my HPDE and by the end of the day my stock pads were completely gone. Got my front rotors and all my pads replaced soon after that. I went for the Ferodo DS2500 pads. While bedding my pads, I noticed the brake feeling/bite is quite nice when braking at around 50-60% pressure, but once I tried emulating track style braking (i.e hitting brake pedal very hard) I noticed that my brake pedal was vibrating/rattling and also felt some sort of scraping was going on. This would happen even when hitting brakes hard from low speeds of ~30 mph. It's felt entirely on the front brakes. ABS did not engage, so I don't think the vibrations are from that. The obvious visible difference I see is the use of high temp brake lube from the shop.

I had a track day today with 1 hour session and closer to the end they were fade.When I took the pads out to check I noticed that they are extremely glazed like covered with a melted metal.Also, looks like they covered rotors with this melted metal, the inner side of both of them.The outer rotors surface is fine. The outer pads look the same glazed.I was checking them yesterday last time and they looked fine.The friction material looked fine and not that glazed.It's on the last photo.I was trying to brake short and strong all the time.There car is Suzuki swift sport.Brake pads ferodo dsuno.Track Zolder.