Brake pads Ferodo or Tesla

Ferodo DS2500 were good in my daily/tracked GTI and track NB Miata, until I got GLOC track pads on the latter. Which are awesome. BUT the DS2500 held up to the track really well, I'd definitely say for a daily that gets tracked they're about as good as you might get. Grease the contact points on the pad with copper or other compatible grease and i think they don't make much noise at all.

I'm running Ferodo DS 1.11. and they're fine on the streets even during winters when it gets even as cold as -25C

I got their vented rear and front rotors (Girodiscs) with stock calipers and Ferrodo DS2500 pads all around. For a stock powered car they work great at VIR. I have done 2 sessions there now and braking is pretty decent. On the street this combo will never fade period. The rears overheat which overload the fronts and cause issues. Rears overheating also causes the wheel bearings to go out so getting vented rears is just smart.

Ferodo DS2500 are a classic high performance street pad, every time I go through a set I am sure something better must have come along and do some market research, always end up back on the DS2500´s as an everday/occasional track pad. They are cheap and they last forever (really) relative to punishment taken, they are dusty though, that´s really my main issue with them.

If you can't find ceramic pads, get Ferodo Premium Eco Friction.

I’ve been using the pads for at least 15k miles on my 2015 evo, haven’t had any issues. Stops perfectly

Ferodo DS2500s were a popular autox/light track pad back in my Subaru days, they did well for me.

I switched to the Ferodo DSUno. I am satisfied with its performance, but they seem to struggle because of something. Today, after the track day on Saturday, I checked it and found a crack and a gnawed edge. Also, they have uneven wear, about 0.5-1mm difference. The differences are between the top and bottom parts of the pads, front and back parts and on different sides of the same rotor (inner and outer pads). Uneven wear was with the old pads as well. Recently, I installed brake air ducts, and after going out from the track, the temperature was, in the worst case, 480C degree, which looks fine for these pads. In total, I drove for about 3 hours on tracks, one on a wet track (so no hard braking) and two moderately/hard(8-9/10) braking. The brake rotors are also new, Zimmermann blank, installed with pads. The initial thickness of the pads is 16.4mm (with the plate, the plate is 5.5mm, so the "pure" pad is about 11mm) Currently, I have eaten about 4.5-5mm of the pads in 3 hours of tracking.

Recently completed my HPDE and by the end of the day my stock pads were completely gone. Got my front rotors and all my pads replaced soon after that. I went for the Ferodo DS2500 pads. While bedding my pads, I noticed the brake feeling/bite is quite nice when braking at around 50-60% pressure, but once I tried emulating track style braking (i.e hitting brake pedal very hard) I noticed that my brake pedal was vibrating/rattling and also felt some sort of scraping was going on. This would happen even when hitting brakes hard from low speeds of ~30 mph. It's felt entirely on the front brakes. ABS did not engage, so I don't think the vibrations are from that. The obvious visible difference I see is the use of high temp brake lube from the shop.

I had a track day today with 1 hour session and closer to the end they were fade.When I took the pads out to check I noticed that they are extremely glazed like covered with a melted metal.Also, looks like they covered rotors with this melted metal, the inner side of both of them.The outer rotors surface is fine. The outer pads look the same glazed.I was checking them yesterday last time and they looked fine.The friction material looked fine and not that glazed.It's on the last photo.I was trying to brake short and strong all the time.There car is Suzuki swift sport.Brake pads ferodo dsuno.Track Zolder.